Antimony telluride with Sb2Te3 chemical formula is a topological insulater.
Particle size: 80mesh, 100mesh
Purity: 99.99%
Antimony Telluride, Sb2Te3-based powder
Chemical formula of antimony telluride: Sb2TE3.Molecularweight 626.30.Gray hard.Melting temperature 639.4.Relative density 6.5018. To dissolve, use nitric. Antimony telluride (covalent bond), ionic bonds, have a certain van Der Waals bond composition, triangular cristal system, original cell is Rhombbus hexahedron.
Telluride is an alveolar layer of antimony layered substances. The layer is comprised of three layers made of atomic antmony and atomic protein. They are held together with weak van den Waals forces. It’s also a topological insulation and has thickness-dependent properties.
It has a rhomboid-shaped crystal structure. The crystalline substance is covalently linked atoms that form five atom-thick layers (in order: Te-Sb Te-Te), which holds the plates together via the Van der Waals Attraction. Bulk telluride, due to its lamellar architecture and weak interlamellar energies can be mechanically separated from the monolayers. Sb2Te3 also has the semiconductor properties of bismuth as well. The powder can be transformed to N and P types of semiconductors by adding appropriate dopants.
Antimony Telluride SB2Te3 powder has these features
Antimony-telluride is an organic compound. The chemical composition is Sb2Te3. Although it is a grey crystal, melting points, densities, and colors may change depending on crystal types. )
Antimony Telluride Powder:
energy gap
Thermoelectric department
Notice: Products can vary in size depending on user needs.
Technical Parameter for Antimony Telluride (Sb2Te3) powder
How are Antimony Telluride (Sb2Te3) powder manufactured?
Telluride antimony preparation is as follows: using SbCl3 and K2TeO3 as starting materials, according to the stoichiometric ratio of n (SbCl3): n (K2TeO3) = 2:3 said take 0.002 mol SbCl3 and 0.003 mol K2TeO3, 250 ml and join the two round bottom flask, and then add in the 0.5 g polyvinylpyrrolidone, 80 ml 0.5 gNaOH and a reduction of diethylene glycol (take) by the measuring cylinder, put two round bottom flask temperature control heating jacket, set the temperature of 240 ° C, insulation 4 h, adjusting the rotational speed of 500 r/min.After the temperature of the reactants dropped to room temperature, the centrifuge was centrifuged 3 times with isopropyl alcohol and acetone, respectively. The centrifuge speed was set for 4000r/min. It took approximately 4 minutes. The top liquid went colorless at the end of centrifugation. To reduce the reactionant’s temperature to 100 ml, centrifuge the tube with isopropanol. It was then dried for 6 hours in an oven before it became a powder of Sb2Te3.
Antimony Telluride HTML3_ :
Sb2Te3 also has semiconducting capabilities, as have other antimony and bismuth binary compounds. The appropriate dopants are required to convert Sb2Te3 into N and P types of semiconductors.
In contrast to single-frequency detection for pure Sb2Te3, iron dipped Sb2Te3 allows multiple Fermi Pockets, which leads to higher mobility and carrier density.
In a pseudo-binary intermetallic Germanium Antimony Telluride System, Sb2Te3 is combined with germanium telluride.
Antimony Telluride, which is similar to bismuth informuride or Bi2Te3, can be found in solid-state refrigerators due to its strong thermoelectric impact.
Antimony Telluride (Sb2Te3) powder stored in a dry place
Store the reservoir tightly sealed.
Shipping & Packaging of Antimony Telluride sb2Te3 powder
Different types of packaging are available depending on Antimony Telluride SB2Te3’s powder amount.
Antimony Telluride SB2Te3 powder packaging in vacuum bags, 100g 500g or 1,kg/bag. 25kg/barrel.
Antimony Telluride SB2Te3 Sb2Te3-powder shipping: could send out via sea, air, or express once the payment has been made.
Antimony Telluride Powder Properties
sesquitelluride
Antimony Telluride Powder Health & Safety Information
Safety Warning
Safety Statements
Inquiry us